Tweco 7-3486 Instrukcja Użytkownika Pobierz pdf

April 30, 2004 / 30 Avril, 2004 1 Manual / Manuel 0-4649

Manual 0-4649

RPT Torch Adapter Kit

No. 7-3486

Installation Instructions

General Information

This kit connects Thermal Dynamics Torches equipped with O2B connectors, or the ATC Adapter Kit, to the following

Power Supplies:

• Lincoln* Pro-Cut 40

Supplied Parts

The kit includes:

• Gas Line Adapter Fitting with O - Ring

• Control Wire Harness with Connector

• Female Faston Terminal

• Instructions

WARNINGS

Disconnect primary input power to the system before starting the installation.

Shut off the gas supply and bleed down the system.

Only a qualified technician should perform this procedure.

Procedure

A. Preparation

1. Remove the Power Supply Cover per the Power Supply Manual.

2. Disconnect the original torch per the Power Supply Manual.

3. Remove the original torch from the Power Supply. Leave the strain relief in place on the power supply.

4. The torch leads or ATC adapter includes a ring terminal on the pilot lead. Pull back the insulating sleeve on the

pilot lead. Cut off the ring terminal. Strip the insulation back approximately 1/4" / 6 mm from the end of the

lead(s). Attach the female Faston terminal included in this kit to the pilot lead. Crimp securely.

5. The torch leads or ATC adapter includes two wires joined together and covered with an insulating sleeve.

Remove the insulating sleeve and disconnect the wires.

6. Remove the strain relief dome nut from the original torch. Install the dome nut on the replacement torch or ATC

adapter.

82 Benning Street, West Lebanon, NH 03784 USA

(603) 298-5711 • www.thermal-dynamics.com

Lincoln is a registered trademark of Lincoln Electric Co., Inc.

1 2 3 4 5 6 7

Podsumowanie treści

Strona 1 - Procedure

April 30, 2004 / 30 Avril, 2004 1 Manual / Manuel 0-4649Manual 0-4649RPT Torch Adapter KitNo. 7-3486Installation InstructionsGeneral InformationThis k

Strona 2 - B. Installation

April 30, 2004 / 30 Avril, 2004 2 Manual / Manuel 0-46497. Check the brass fitting included in this kit. There is an O - Ring installed in the female

Strona 3 - D. Pinout Diagram

April 30, 2004 / 30 Avril, 2004 3 Manual / Manuel 0-46495. Connect the RPT Adapter Kit wire harness connector to the receptacle on the Power Supply to

Strona 4

April 30, 2004 / 30 Avril, 2004 4 Manual / Manuel 0-4649

Strona 5 - Informations Générales

April 30, 2004 / 30 Avril, 2004 5 Manual / Manuel 0-464982 Benning Street, West Lebanon, NH 03784 USA(603) 298-5711 • www.thermal-dynamics.comManuel

Strona 6

April 30, 2004 / 30 Avril, 2004 6 Manual / Manuel 0-46497. Vérifiez le raccord en laiton inclus dans ce kit. Il y a un joint torique installé dans le

Strona 7 - D. Diagramme De Pinout

April 30, 2004 / 30 Avril, 2004 7 Manual / Manuel 0-46496. Connectez le connecteur femelle de ‘Faston’ sur les fils de torche ou l’adapteur d’ATC marq

Komentarze do niniejszej Instrukcji

Brak uwag

Tweco 7-3486 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Tweco 7-3486. Tweco 7-3486 Manuel d'utilisation Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Tweco 7-3486