Tweco 7-3457 Instrukcja Użytkownika Pobierz pdf

Manual / Manuel 0-2891 1 June 16, 2003 / 16 Juin, 2003

Manual 0-2891

RPT Adapter Kits

Catalog # 7-3454, 7-3457

Installation Instructions

General Information

These Replacement Torch Adapter Kits connect the Thermal Dynamics SL60 and SL100 Torch Leads with O2B fit-

tings, or ATC Adapter Kit No. 7-5207, to the following equipment:

• Kit No. 7-3454: Hypertherm* powermax* 600, 800, 900; Max* 42, 43, 40cs

• Kit No. 7-3457: Miller* Spectrum* 650, 701, 2050

Supplied Parts

The kits include:

• Adapter Assembly

• Large Insulating Sleeve

• Small Insulating Sleeve

• Bushing (used for 60-amp torch leads only)

• Instructions

Assembly

Hypertherm, powermax, and Max are registered trademarks of Hypertherm, Inc.

Miller

and

Spectrum are registered trademarks of Miller Electric Co., Inc.

82 Benning Street, West Lebanon, NH 03784 USA

(603) 298-5711 • www.thermal-dynamics.com

WARNING

Disconnect primary power to the

system before disassembling the

torch or torch leads.

CAUTION

The Adapter includes a fender washer or protective end cap, held in place by a

screw. Leave the washer and screw in place until the RPT Adapter Kit is com-

pletely connected to the ATC Adapter Kit.

Connect the RPT Adapter Kit as follows:

1. Refer to the illustration. Remove 4 screws from the shell halves.

2. Separate the shell halves at the large end. Pull the shell halves away from each

other. Twist them out of the connecting ring to remove them from the assembly.

3. Cut the plastic tie wrap off the sleeved wire on the ATC adapter or torch leads.

Remove the sleeve. Disconnect the mating connectors from each other.

4. Cut the ring tongue connector off the sleeved wire on the ATC adapter or torch

leads. Strip approximately 1/4 inch / 6 mm of insulation from the end of the wire.

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - Assembly

Manual / Manuel 0-2891 1 June 16, 2003 / 16 Juin, 2003Manual 0-2891RPT Adapter KitsCatalog # 7-3454, 7-3457Installation InstructionsGeneral Informat

Strona 2

Manual / Manuel 0-2891 2 June 16, 2003 / 16 Juin, 20035. Slide the large insulating sleeve onto the Negative / Plasma lead (only) on the ATC adapter

Strona 3 - Connector Pin Layout

Manual / Manuel 0-2891 3 June 16, 2003 / 16 Juin, 2003Installation and Use1. Use the connecting ring on the ATC Adapter Kit to secure the male conne

Strona 4

Manual / Manuel 0-2891 4 June 16, 2003 / 16 Juin, 2003

Strona 5 - Catalogue # 7-3454, 7-3457

Manual / Manuel 0-2891 5 June 16, 2003 / 16 Juin, 200382 Benning Street, West Lebanon, NH 03784 USA(603) 298-5711 • www.thermal-dynamics.com AV

Strona 6 - A-03422F

Manual / Manuel 0-2891 6 June 16, 2003 / 16 Juin, 20035. Glissière la grande douille isolante sur le fil négatif / plasma (seulement) sur les fils d’

Strona 7 - Installation et Utilisation

Manual / Manuel 0-2891 7 June 16, 2003 / 16 Juin, 200311. Position le deuxième coque demi sur l’assemblée. Torsion il en l’ajustement d’place il dan

Strona 8 - A-03511F

Manual / Manuel 0-2891 8 June 16, 2003 / 16 Juin, 2003Disposition De Goupille De ConnecteurA-03511FDisposition de goupille d'adapteur de Hyperth

Powiązane modele: 7-3454

Komentarze do niniejszej Instrukcji

Brak uwag

Tweco 7-3457 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Tweco 7-3457. Tweco 7-3457 Manuel d'utilisation Instrukcja obsługi

Podsumowanie treści

Powiązane modele: 7-3454

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Tweco 7-3457