Tweco Torch Data for Auto-Cut O2 V.2 Instrukcja Użytkownika Pobierz pdf (Strona 30)

TORCH DATA for AutoCut O

8-30 Manual 0-4832 Rev AF

(ga) (in) inch (PSI)

(Ball

)

(PSI)

(Ball

)

(PSI) Volts

(in)

±0.005

(ipm) (in) (sec) (in)

1/2 0.500 20 100 90 5 55 168 0.250 110 0.300 0.3 0.120

5/8 0.625 20 80 100 5 55 170 0.300 105 0.350 0.5 0.126

3/4 0.750 20 80 100 5 55 175 0.300 90 0.350 0.6 0.127

7/8 0.875 20 80 100 5 55 180 0.300 75 0.350 0.8 0.133

1 1.000 20 80 100 5 55 194 0.350 50 0.400 1.0 0.144

1 1/4 1.250 20 80 100 5 55 208 0.400 25 0.450 2.0 0.180

1 1/2 1.500 20 80 100 5 55 210 0.400 20 0.500 3.000 0.197

1 3/4 1.750 20 80 100

55 212 0.400 18 0.201

2 2.000 20 80 100

55 215 0.400 12 0.204

(Bar)

(Ball

)

(Bar)

(Ball

)

(Bar) Volts

(mm)

±0.1

(mm/min)

(mm) (sec) (mm)

1.4 100 6.3 5 3.8 167 6.3 2900 7.6 0.3 3.0

1.4 80 6.9 5 3.8 170 7.5 2700 8.9 0.5 3.2

1.4 80 6.9 5 3.8 176 7.5 2200 8.9 0.6 3.3

1.4 80 6.9 5 3.8 194 8.9 1300 10.2 1.0 3.6

1.4 80 6.9 5 3.8 208 10.2 630 11.4 2.0 4.6

1.4 80 6.9 5 3.8 210 10.2 500 12.7 3.0 5.0

1.4 80 6.9 5 3.8 212 10.2 460 5.1

1.4 80 6.9

3.8 215 10.2 300 5.2

* Pressure of the water supply line should be regulated by customer pressure regulator.

Note1:

Ohmic height sensing is not recommended with water shield. Water on the plate interferes electrically with the

ohmic sensing circuit.

Note2:

Water source used for shield must be demineralized.

Aluminum

200A

Plasma / H

O Shield

BOLD TYPE

indicates maximum piercing parameters.

BOLD ITALIC

indicates edge starts only.

Requires CCM version 3.4 or later. Requires GCM version 3.2 or later.

50 Edge Start

44 Edge Start

Kerf Width

@ Rec.

Speed

Plasma (N

)

Shield

O)*

(mm)

Edge Start

Material

Thickness

Pre Flow

Pressure

)

Cut Flow Rates /

Pressures

Arc

Voltage

Torch

Working

Height

Travel

Speed

Initial

Piercing

Height

Pierce

Delay

Kerf Width

@ Rec.

Speed

Plasma (N

)

Shield

O)*

Edge Start

Torch

Working

Height

Travel

Speed

Initial

Piercing

Height

Pierce

Delay

Material

Thickness

Pre Flow

Pressure

)

Cut Flow Rates /

Pressures Arc

Voltage

36-1048 36-1089 36-102036-1016 36-1039 36-1273 36-1064

Plasma Gas

Distributor

Electrode CartridgeShield Cup Shield Cap

Shield Gas

Distributor

Tip

Electrode

Shield Cap

Tip

Shield Gas

Distributor

Plasma Gas

Distributor

Cartridge

Shield Cup

This Art Is For Reference ONLY

Art # A-07958_AB

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 53 54

Komentarze do niniejszej Instrukcji

Brak uwag

Tweco Torch Data for Auto-Cut O2 V.2 Instrukcja Użytkownika Strona 30

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Tweco Torch Data for Auto-Cut O2 V.2