Tweco Torch Data for Auto-Cut O2 V.2 Instrukcja Użytkownika Pobierz pdf (Strona 10)

TORCH DATA for AutoCut O

8-10 Manual 0-4832 Rev AF

Mild Steel

100A

Air Plasma / Air Shield

(ga) (in) inch psi Ball psi Ball psi Volts

(in)

±0.005

(ipm) (in) (sec) (in)

16 0.060 74 58 90 90 90 150 0.110 600 0.250 0.1 0.072

10 0.135 74 58 90 90 90 150 0.110 300 0.250 0.2 0.065

3/16 0.188 74 58 90 90 90 150 0.110 210 0.250 0.3 0.073

1/4 0.250 74 58 90 90 90 155 0.120 150 0.300 0.3 0.078

3/8 0.375 74 58 90 90 90 155 0.130 85 0.300 0.3 0.091

1/2 0.500 74 58 90 43 90 157 0.140 75 0.300 0.3 0.095

5/8 0.625 74 58 90 43 90 165 0.140 55 0.350 0.5 0.099

3/4 0.750 74 58 90 43 90 168 0.150 30 0.350 0.6 0.120

1 1.000 74 58 90 43 90 180 0.200 20 0.112

bar Ball bar Ball bar Volts

(mm)

±0.1

(mm/min) (mm) (sec) (mm)

5.1 58 6.2 90 6.2 150 2.8 13340 6.4 0.1 1.8

5.1 58 6.2 90 6.2 150 2.8 9340 6.4 0.2 1.7

5.1 58 6.2 90 6.2 150 2.8 6650 6.4 0.2 1.7

5.1 58 6.2 90 6.2 151 2.8 5120 6.5 0.3 1.9

5.1 58 6.2 90 6.2 154 3.0 4150 7.3 0.3 2.0

5.1 58 6.2 90 6.2 155 3.2 2950 7.6 0.3 2.2

5.1 58 6.2 90 6.2 155 3.3 2120 7.6 0.3 2.3

5.1 58 6.2 45 6.2 157 3.5 1960 7.6 0.3 2.4

5.1 58 6.2 45 6.2 163 3.6 1540 8.5 0.4 2.5

5.1 58 6.2 45 6.2 170 4.0 720 9.5 0.6 3.0

5.1 58 6.2 45 6.2 179 5.0 520 2.9

Edge Start

Pre Flow

Pressure

(Air)

Cut Flow Rates / Pressures

Plasma (Air) Shield (Air)

Pre Flow

Pressure

(Air)

Cut Flow Rates / Pressures

Plasma (Air) Shield (Air)

Initial

Piercing

Height

(mm)

Pierce

Delay

Kerf

Width

@ Rec.

Speed

Material

Thickness

Arc

Voltage

Torch

Working

Height

Travel

Speed

Bold type

indicates maximum piercing parameters.

Bold italic

indicates edge starts only.

100A Mild Steel (Air/Air)

Material

Thickness

Arc

Voltage

Torch

Working

Height

Travel

Speed

Initial

Piercing

Height

Pierce

Delay

Kerf

Width

@ Rec.

Speed

Edge Start

Cartridge

36-1020

Shield Cup

36-1016

Shield Cap

36-1027

Shield Gas Distributor

36-1272

Tip

36-1053

Plasma Gas Distributor

36-1041

Electrode

36-1071

Art # A-07304

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 53 54

Komentarze do niniejszej Instrukcji

Brak uwag

Tweco Torch Data for Auto-Cut O2 V.2 Instrukcja Użytkownika Strona 10

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Tweco Torch Data for Auto-Cut O2 V.2