Tweco XT-301 Torch Data for OEM use w- Auto-Cut 30O2 AD Instrukcja Użytkownika Pobierz pdf

Manual 0-4832 Rev AD 8-1 TORCH DATA for AutoCut O

8. TORCH OPERATION

Torch Parts Selection

The application will determine which torch parts must be used. Refer to the cut charts for the proper torch parts to

install for a selected application.

CAUTION

Do not interchange parts. Make sure all torch parts correspond with the

plasma and shield gases in use for the application.

Pre-Setting Power Supply Controls

Set the Power Supply controls prior to operating the system as described in the power supply Operating Manual.

Refer to the cutting charts for the proper cutting parameters for the application.

Recommended Cutting Speeds

Cutting speed depends on material and thickness. The following factors may affect system performance:

• Torch parts wear; gas quality and mass flow / pressure; operator experience; torch standoff height; proper

work cable connection; alloying contents of material; cutting table capabilities & accuracy.

NOTE

This information represents realistic expectations using recommended

practices and well-maintained systems. Actual speeds may vary from

those shown in the charts depending on the alloy content of the selected

material. Voltage ratings may vary depending on the CNC, cutting table,

or height controller.

For complete cutting speed chart data refer to the following pages.

Consumables Notes

Always assemble the consumable parts properly. Improper assembly may damage the parts or the torch head.

Ensure that parts are seated together correctly.

Always check the shield gas distributor for charring when changing parts. Do not use the distributor if it is charred.

Replace the shield gas distributor regularly to ensure proper performance.

Operational Notes

Always purge the torch after changing consumables or if the power supply has been shut off. The power supply's

built-in purge function may not be enough to properly purge the torch. Manually flow gas with the 'Test Cut Flow' and

'Test Pre-Flow' functions to help remove any remaining coolant from the lines.

Slightly increasing the preflow pressure may increase piercing ability on thicker materials. However, increasing the

preflow pressure too much may affect plasma starting reliability (misfiring).

Decreasing preflow pressure may improve piloting. Preflow pressure can be reduced without affecting cut perfor-

mance as long as the pilot arc still transfers to the plate well. Decreasing preflow pressure too much will affect the

ability to transfer the arc to the plate.

Notes on Chart Measurements

Pressure measurements in the charts are in psi(g), not psi(a). 0 psi(g) = 14.7 psi(a) (1 atmosphere).

Ball settings are at the center of the guage ball.

1 2 3 4 5 6 ... 53 54

Podsumowanie treści

Strona 1 - 8. TORCH OPERATION

Manual 0-4832 Rev AD 8-1 TORCH DATA for AutoCut O28. TORCH OPERATIONTorch Parts SelectionThe application will determine which torch parts must be

Strona 2 - Underwater Cutting

TORCH DATA for AutoCut O28-10 Manual 0-4832 Rev ADMild Steel100AAir Plasma / Air Shield(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (i

Strona 3

Manual 0-4832 Rev AD 8-11 TORCH DATA for AutoCut O2(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)16 0.063 90 58 90 75 90 1

Strona 4 - 8-4 Manual 0-4832 Rev AD

TORCH DATA for AutoCut O28-12 Manual 0-4832 Rev AD(ga) (in) inch (PSI) Ball (PSI) Ball (PSI) Volts(in)±0.005(ipm) (in) (sec) (in)3/8 0.375 40 65 120

Strona 5 - Plasma / Air Shield

Manual 0-4832 Rev AD 8-13 TORCH DATA for AutoCut O2(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)10 0.141 80 60 120 5 55 1

Strona 6

TORCH DATA for AutoCut O28-14 Manual 0-4832 Rev ADAluminum100AAir Plasma / Air Shield(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in)

Strona 7

Manual 0-4832 Rev AD 8-15 TORCH DATA for AutoCut O2(ga) (in) inch (PSI) Ball (PSI) Ball (PSI) Volts(in)±0.005(ipm) (in) (sec) (in)3/8 0.375 40 68 120

Strona 8

TORCH DATA for AutoCut O28-16 Manual 0-4832 Rev ADAluminum100AN2 Plasma / H2O Shield(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in)

Strona 9

Manual 0-4832 Rev AD 8-17 TORCH DATA for AutoCut O2(ga) (in) inch (PSI) (Ball) (PSI)(Ball)(PSI) Volts(in)±0.005(ipm) (in) (sec) (in)3/8 0.375 1/2 0.5

Strona 10 - Air Plasma / Air Shield

TORCH DATA for AutoCut O28-18 Manual 0-4832 Rev ADThis Page Intentionally Blank

Strona 11 - Stainless Steel

Manual 0-4832 Rev AD 8-19 TORCH DATA for AutoCut O2Material Gases UsedConsumable Description100A 55AElectrode36-1071 36-1069Plasma Gas Distributor36-

Strona 12 - H35 Plasma / N

TORCH DATA for AutoCut O28-2 Manual 0-4832 Rev ADOhmic SensingOhmic sensing is not recommended with water shield. Water on the plate interferes elec

Strona 13 - O Shield

TORCH DATA for AutoCut O28-20 Manual 0-4832 Rev ADThis Page Intentionally Blank

Strona 14 - Aluminum

Manual 0-4832 Rev AD 8-21 TORCH DATA for AutoCut O2Insert "200 Amp" Tab.Discard this sheet.

Strona 15

TORCH DATA for AutoCut O28-22 Manual 0-4832 Rev AD

Strona 16 - TORCH DATA for AutoCut O

Manual 0-4832 Rev AD 8-23 TORCH DATA for AutoCut O2Mild Steel200AO2 Plasma / Air Shield36-101836-101936-102936-128136-105636-108636-1020ShieldRetai

Strona 17 - Make Copies as Desired

TORCH DATA for AutoCut O28-24 Manual 0-4832 Rev ADMild Steel200AAir Plasma / Air Shield(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (i

Strona 18 - This Page Intentionally Blank

Manual 0-4832 Rev AD 8-25 TORCH DATA for AutoCut O2Stainless Steel200AAir Plasma / Air Shield36-101836-101936-128136-105736-108536-1020ShieldRetainer

Strona 19 - Auto-Cut-O2

TORCH DATA for AutoCut O28-26 Manual 0-4832 Rev ADStainless Steel200AH35 Plasma / N2 Shield **Plasma (H35) Shield (N2) (ga) (in) inch (PSI) (PSI)

Strona 20 - 8-20 Manual 0-4832 Rev AD

Manual 0-4832 Rev AD 8-27 TORCH DATA for AutoCut O2(ga) (in) inch (PSI) (Ball) (PSI) (Ball) (PSI) Volts(in)±0.005(ipm) (in) (sec) (in)3/8 0.375 20 80

Strona 21 - Discard this sheet

TORCH DATA for AutoCut O28-28 Manual 0-4832 Rev ADAluminum200AAir Plasma / Air Shield(ga) (in) inch (PSI) Ball (PSI) Ball (PSI) Volts(in)±0.005(ipm

Strona 22 - 8-22 Manual 0-4832 Rev AD

Manual 0-4832 Rev AD 8-29 TORCH DATA for AutoCut O2Aluminum200AH35 Plasma / N2 Shield **36-1273Shield Cup 36-1016Shield GasDistributorTip36-1058Art

Strona 23 - Art # A-07307

Manual 0-4832 Rev AD 8-3 TORCH DATA for AutoCut O2Insert "Up To 100 Amp" Tab.Discard this sheet.

Strona 24

TORCH DATA for AutoCut O28-30 Manual 0-4832 Rev AD(ga) (in) inch (PSI)(Ball)(PSI)(Ball)(PSI) Volts(in)±0.005(ipm) (in) (sec) (in)1/2 0.500 20 100 90

Strona 25 - Air Plasma / Air Shield

Manual 0-4832 Rev AD 8-31 TORCH DATA for AutoCut O2(ga) (in) inch (PSI) (Ball) (PSI)(Ball)(PSI) Volts(in)±0.005(ipm) (in) (sec) (in)3/8 0.375 1/2 0.5

Strona 26 - Shield **

TORCH DATA for AutoCut O28-32 Manual 0-4832 Rev ADThis Page Intentionally Blank

Strona 27 - O Shield

Manual 0-4832 Rev AD 8-33 TORCH DATA for AutoCut O2Material Gases UsedConsumable Description200A 100A 55AElectrode36-1085 Air/Air 36-1071 36-106936-1

Strona 28

TORCH DATA for AutoCut O28-34 Manual 0-4832 Rev ADThis Page Intentionally Blank

Strona 29 - Shield **

Manual 0-4832 Rev AD 8-35 TORCH DATA for AutoCut O2Insert "300 Amp" Tab.Discard this sheet.

Strona 30

TORCH DATA for AutoCut O28-36 Manual 0-4832 Rev AD

Strona 31

Manual 0-4832 Rev AD 8-37 TORCH DATA for AutoCut O2(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)1/2 0.500 15 104 90 NA 40

Strona 32 - 8-32 Manual 0-4832 Rev AD

TORCH DATA for AutoCut O28-38 Manual 0-4832 Rev AD(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)3/8 0.375 20 120 100 NA 12

Strona 33

Manual 0-4832 Rev AD 8-39 TORCH DATA for AutoCut O2(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)3/8 0.375 20 120 100 8 55

Strona 34 - 8-34 Manual 0-4832 Rev AD

TORCH DATA for AutoCut O28-4 Manual 0-4832 Rev ADThis Page Intentionally Blank

Strona 35

TORCH DATA for AutoCut O28-40 Manual 0-4832 Rev AD(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)1/4 0.250 20 120 100 NA 12

Strona 36 - 8-36 Manual 0-4832 Rev AD

Manual 0-4832 Rev AD 8-41 TORCH DATA for AutoCut O2(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)1/2 0.500 20 120 100 8 55

Strona 37 - Plasma / Air Shield

TORCH DATA for AutoCut O28-42 Manual 0-4832 Rev ADThis Page Intentionally Blank

Strona 38

Manual 0-4832 Rev AD 8-43 TORCH DATA for AutoCut O2(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)1/2 5/8 3/47/811 1/41 1/2

Strona 39

TORCH DATA for AutoCut O28-44 Manual 0-4832 Rev ADThis Page Intentionally Blank

Strona 40

Manual 0-4832 Rev AD 8-45 TORCH DATA for AutoCut O2Material Gases UsedConsumable Description300A 200A 100A 55APlasma Gas Distributor36-1044 Air/Air3

Strona 41 - Aluminium

TORCH DATA for AutoCut O28-46 Manual 0-4832 Rev ADThis Page Intentionally Blank

Strona 42 - 8-42 Manual 0-4832 Rev AD

Manual 0-4832 Rev AD 8-47 TORCH DATA for AutoCut O2Insert "Torch Appendix" TabDiscard this sheet.

Strona 43

TORCH DATA for AutoCut O28-48 Manual 0-4832 Rev AD

Strona 44 - 8-44 Manual 0-4832 Rev AD

Manual 0-4832 Rev AD 8-49 TORCH DATA for AutoCut O2O-Ring, Cat. No. 8-0544Inner O-Ring (Cat. No. 8-0545) Location (Under Locking Ring)O-Ring, Cat. No

Strona 45 - Auto-Cut-300-O2

Manual 0-4832 Rev AD 8-5 TORCH DATA for AutoCut O2Mild Steel55AO2 Plasma / Air ShieldTip36-1272ElectrodeShield Cap36-102536-105136-106936-1041 Car

Strona 46 - 8-46 Manual 0-4832 Rev AD

TORCH DATA for AutoCut O28-50 Manual 0-4832 Rev ADCartridge Assembly (36-1022) Consumables2x-100536-100736-102336-1022Art # A-09243Shield CupBafﬂeCar

Strona 47

Manual 0-4832 Rev AD 8-51 TORCH DATA for AutoCut O2End CapCoolant Supply,Coolant Return,and Pilot LeadsLeads CoverTo Torch ValveArt # A-06981To Remot

Strona 48 - 8-48 Manual 0-4832 Rev AD

TORCH DATA for AutoCut O28-52 Manual 0-4832 Rev ADO-Ring Selection for Torch Consumable PartsArt # A-07249_AB36-103436-105136-106036-106936-1078O-Rin

Strona 49 - TORCH REPLACEMENT PARTS

Manual 0-4832 Rev AD 8-53 TORCH DATA for AutoCut O2PATENT INFORMATIONXTTM-301 Plasma Cutting Torch PatentsThe following parts are covered under U.S.

Strona 50 - 8-50 Manual 0-4832 Rev AD

TORCH DATA for AutoCut O28-54 Manual 0-4832 Rev ADXTTM-301 Plasma Cutting Torch PatentsThe following parts are covered under U.S. and Foreign Patents

Strona 51 - Art # A-06981

TORCH DATA for AutoCut O28-6 Manual 0-4832 Rev ADMild Steel55AAir Plasma / Air Shield(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in)

Strona 52

Manual 0-4832 Rev AD 8-7 TORCH DATA for AutoCut O2Stainless Steel55AAir Plasma / Air Shield(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm

Strona 53 - PATENT INFORMATION

TORCH DATA for AutoCut O28-8 Manual 0-4832 Rev AD(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)23 0.031 90 45 90 55 90 120

Strona 54

Manual 0-4832 Rev AD 8-9 TORCH DATA for AutoCut O2(ga) (in) inch psi Ball psi Ball psi Volts(in)±0.005(ipm) (in) (sec) (in)16 0.060 74 56 120 90 90 1

Komentarze do niniejszej Instrukcji

Brak uwag

Tweco XT-301 Torch Data for OEM use w- Auto-Cut 30O2 AD Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Tweco XT-301 Torch Data for OEM use w- Auto-Cut 30O2 AD. Tweco XT-301 Torch Data for OEM use w- Auto-Cut 30O2 AD User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Tweco XT-301 Torch Data for OEM use w- Auto-Cut 30O2 AD